Praseodymia on non-passivated and passivated Si(111) surfaces

Bitte benutzen Sie diese Kennung, um auf die Ressource zu verweisen: https://repositorium.ub.uni-osnabrueck.de/handle/urn:nbn:de:gbv:700-201107048169
Titel: Praseodymia on non-passivated and passivated Si(111) surfaces
Autor(en): Gevers, Sebastian
Erstgutachter: Prof. Dr. Joachim Wollschläger
Zweitgutachter: Prof. Dr. Michael Reichling
Zusammenfassung: In the presented thesis thin praseodymia films on non-passivated and passivated Si(111) substrates were investigated. The first part deals with PDA of praseodymia films with fluorite structure under UHV conditions in the temperature region from RT to 600°C. Here, a sophisticated model of the annealing process of praseodymia films is established. This is done by detailed analysis of XRD measurements using the kinematic diffraction theory in combination with the analysis of GIXRD, XRR and SPA-LEED measurements. It is shown that the untreated films, which are oxidized in 1 atm oxygen to obtain fluorite structure, do not exhibit pure PrO2 stoichiometry as it was assumed before. Instead, they decompose into two laterally coexisting species exhibiting a PrO2 and a Pr6O11. oxide phase, respectively. These species are laterally pinned to the lattice parameter of bulk Pr6O11. Homogeneous oxide films with Pr6O11 phase can be observed after annealing at 100°C and 150°C. Here, lateral strain caused by the pinning of the species is minimized and an increase of the crystallite sizes is determined. If higher annealing temperatures are applied, the film decomposes again into two coexisting species. Finally, after annealing at 300°C, a mixed crystalline film with both Pr2O3 and Pr2O3+Delta oxide phases is formed, where Delta denotes a considerable excess of oxygen within the sesquioxide phase. Again the lateral strain increases due to the tendency of praseodymia phases to increase their lattice parameters during oxygen loss combined with the lateral pinning. This is accompanied by a decrease of crystallite sizes, which are afterwards comparable to those of the untreated films. Further annealing at temperatures above 300°C does not significantly change the structure of the oxide film. However, the increase of the amorphous Pr-silicate interface between Si substrate and oxide at the expense of the crystalline oxide can be observed after annealing at higher temperatures. Furthermore, an increased mosaic spread of the crystallites occurs, which reduces the lateral strain caused by the oxygen loss. Nevertheless, the crystalline structure is stable against further annealing up to temperatures of 600°C. Transportation of the sample under ambient conditions after annealing at 200°C and 300°C leads to the formation of an additional crystalline structure at the surface which cannot be allocated to any praseodymia phase and may be explained by the contamination of the topmost crystalline layers with Pr-hydroxides. The results obtained from praseodymia films annealed in 1 atm nitrogen show that these films are good candidates to form homogeneous oxide films with pure cub-Pr2O3 structure by subsequent annealing in UHV. Here, a single oxide species is already observed after annealing at 300°C by SPA-LEED measurements which is in contrast to praseodymia films with fluorite structure where higher annealing temperatures (600°C) are necessary. In this case, negative effects like interface growth or increased defect density (mosaics, grain boundaries) can be minimized. Investigations on oxygen plasma-treated praseodymia films to obtain pure PrO2 stoichiometry are presented in the second part. Oxygen plasma-treated samples are compared with samples oxidized in 1 atm oxygen regarding the structure of the crystalline film. For this purpose, XRR and XRD measurements are performed to get structural information of the oxide film, which can be used to identify the corresponding oxide phases. Here, significantly smaller lattice constants of the crystalline oxide species can be observed after plasma treatment, which points to the incorporation of additional oxygen atoms. This verifies former studies, where a higher oxidation state of the oxide film was found by XPS measurements and it shows that plasma-treated films exhibit a higher oxidation state than films oxidized in 1 atm oxygen due to the availability of reactive atomic oxygen in the plasma. Furthermore, the Pr-silicate interface between crystalline film and Si substrate is not increased during plasma treatment. In the last part of the presented thesis, first results from the epitaxy of praseodymia films on Cl-passivated Si substrates are shown. The aim is to suppress the Pr-silicate formation during the growth process. Thus, praseodymia films are grown on passivated and non-passivated substrates to compare the crystallinity of both samples using XSW and LEED measurements. The structure of the oxide films on Cl-passivated Si is determined afterwards by XRR. It is shown that crystalline films with cub-Pr2O3 structure and several nanometer thickness can be successfully grown on Cl-passivated substrates. Here, the Pr-silicate interface layer are restricted to a single mono-layer. In contrast, the films grown on non-passivated substrates are completely amorphous containing Pr-silicates and Pr-silicides.
URL: https://repositorium.ub.uni-osnabrueck.de/handle/urn:nbn:de:gbv:700-201107048169
Schlagworte: Thin Films; Praseodymium oxide
Erscheinungsdatum: 4-Jul-2011
Enthalten in den Sammlungen:FB04 - E-Dissertationen

Dateien zu dieser Ressource:
Datei Beschreibung GrößeFormat 
thesis_gevers.pdfPräsentationsformat7,76 MBAdobe PDFMiniaturbild
Öffnen/Anzeigen


Diese Ressource wurde unter folgender Copyright-Bestimmung veröffentlicht: Lizenz von Creative Commons Creative Commons